Lawn Calculator

Artificial Turf Calculator

Plan a synthetic grass lawn the way it is ordered: whole strips from a 15 ft or 12 ft wide roll, cut to length. Enter the lawn's length and width to get the strips, turf to order, seam length, infill pounds and bags, base gravel in cubic yards and tons, and the soil to dig out. For natural grass, use the sod calculator or the grass seed calculator.

Quick answer

A 30 x 20 ft lawn on 15 ft rolls needs 2 strips cut 30 ft long: 900 sq ft of turf and 30.0 ft of seam.

Silica sand infill at 2.0 lb per sq ft is 1,200 lb (24 bags of 50 lb), and a 3 in base is 5.56 cu yd, about 7.78 tons.

Turf, Seams, Infill and Base

Rectangle layout or total area · results update as you type

Lawn length and width

Plain numbers with a period for decimals, such as 20 or 12.5.

Most landscape turf is 15 ft wide, some 12 ft. Any width from 3 to 20 ft.

Width cut off at each seam so the edges butt cleanly. 0 to 12 in; 0 if you butt factory edges.

Extra length added to each strip, 0 to 24 in. Strip lengths are always rounded up to a whole foot.

Use your turf maker's rate if it gives one. Up to 10 lb per sq ft.

1 to 2,000 lb. Bags are rounded up.

Compacted crushed stone, decomposed granite or class 2 road base. Up to 12 in.

0 to 40%. Compacted base needs more loose material; ask your supplier how much to add.

0.5 to 2.5. The default matches our paver base calculator; enter your supplier's figure if you have one.

0 to 6 in. Installation guides dig about 1 in deeper than the base.

Enter the lawn length and width, or load the 30 x 20 ft example.

Your result (planning estimate)

Turf to order —
Strips—
Seam length (seam tape)—
Extra over lawn area—
Infill—
Base—
Excavation—

How the Artificial Turf Calculator Works

Turf is sold from rolls of a fixed width and cut to length, not to width [T4]. So the question is how many strips of the roll width cover the lawn, and how long each strip must be.

Strips, turf to order and seams

Strips n = 1 if the span fits on one roll, otherwise n = ⌈(span − trim) ÷ (roll width − trim)⌉

  • Span is the side across the strips and run is the side along them. Each seam loses the seam trim, because the overlap is cut away so the edges butt [T1] [T5] [T8].
  • Strip length = run + end allowance, rounded up to the next whole foot [T1] [T4].
  • Turf to order = strips × roll width × strip length (sq ft). Linear feet of roll = strips × strip length.
  • Seam length = (strips − 1) × run. Seam tape covers the same length.
  • The calculator works out both run directions and picks the one with less turf; on a tie, the shorter seam; on a full tie, strips along the length. The other direction is shown as the alternative.

Total area (irregular lawns)

Turf to order = area × (1 + waste ÷ 100)

Waste is 10% by default [T3], with a 20% preset for complex shapes [T5]. Area mode does not plan strips or seams.

Infill, base and excavation

These use the lawn area itself, not the turf ordered:

  • Infill (lb) = lawn area × infill rate; bags = infill ÷ bag size, rounded up.
  • Base (cu yd) = lawn area × base depth (in) ÷ 12 ÷ 27 × (1 + compaction ÷ 100); tons = cu yd × density.
  • Dig depth = base depth + extra dig; soil removed (cu yd) = lawn area × dig depth (in) ÷ 12 ÷ 27, measured in the ground before it loosens.

Metric lengths are converted exactly (1 ft = 0.3048 m) and kilograms use 1 lb = 0.45359237 kg [NIST].

Worked Examples: Common Lawn Sizes

Default values: 15 ft roll, 3 in seam trim, silica sand infill at 2.0 lb per sq ft in 50 lb bags, 3 in base at 1.4 tons per cu yd.

Lawn (ft)Strips × lengthTurf to order (sq ft)Seam (ft)Extra over lawnInfill (lb, bags)Base (cu yd, tons)
15 x 151 × 15 ft2250.00.0%450 lb, 9 bags2.08 cu yd, 2.92 t
27 x 141 × 27 ft4050.07.1%756 lb, 16 bags3.50 cu yd, 4.90 t
30 x 202 × 30 ft90030.050.0%1,200 lb, 24 bags5.56 cu yd, 7.78 t
40 x 303 × 30 ft1,35060.012.5%2,400 lb, 48 bags11.11 cu yd, 15.56 t
50 x 252 × 50 ft1,50050.020.0%2,500 lb, 50 bags11.57 cu yd, 16.20 t
60 x 403 × 60 ft2,700120.012.5%4,800 lb, 96 bags22.22 cu yd, 31.11 t

A 40 x 30 ft lawn shows why seam trim matters: 2 strips of 15 ft are exactly 30 ft wide, which leaves nothing for the trim, so the calculator runs 3 strips the other way instead.

Typical Values and Installation Notes

  • Roll width: most landscape turf comes in 15 ft wide rolls, some in 12 ft [T1] [T2] [T3] [T4]. Rolls are cut to length, not width [T4].
  • Direction: lay all pieces with the blades facing the same direction [T1] [T3] [T5] [T8] [T9] [T10].
  • Infill: silica sand is commonly 1.5 to 3 lb per sq ft and coated infills 2.5 to 3.5 lb per sq ft [T5] [T6] [T7] [T8]. Use your turf maker's figure if it gives one: some products specify much more (5.5 to 6 lb) [T2].
  • Base: 2 to 4 in of compacted crushed stone, decomposed granite or class 2 road base, about 3 in being common; use 4 in where the ground freezes [T1] [T9] [T10].
  • Excavation: dig about 1 in deeper than the base [T9] [T10].
  • Base weight: installer rules of thumb work out to about 1.0 to 1.1 tons per cu yd [T1] [T8]. The default here is 1.4, the same as our paver base calculator, so it orders a little more. Change it to your supplier's figure.

Common Mistakes

  • Dividing the area by the roll width. You buy whole strips, so the offcut along the last strip is part of the order.
  • Forgetting the seam trim. A lawn exactly two roll widths wide does not fit on two strips once the seam edges are cut.
  • Ordering infill and base for the turf ordered. Both go on the lawn itself, so they use the lawn area, not the larger turf order.
  • Mixing pile directions. Pieces laid with the blades in different directions show a visible color change at the seam.

Need the base material on its own? See the decomposed granite calculator, the crusher run calculator or the gravel calculator. To size the dig, use the excavation calculator.

Sources and Limits

Sources accessed November 13, 2026:

  1. [T1] Greatmats, GrassTex outdoor artificial turf installation guide (PDF): 12 ft and 15 ft widths, seam overlap of at least 3 in that is cut, round lengths up, 2 to 4 in compacted base, 2 to 3 lb of silica sand.
  2. [T2] Greatmats, Troon landscaping turf product page: 15 ft fabric width, 4 in crushed stone base, 5.5 to 6 lb of silica sand recommended for that product.
  3. [T3] Patio Productions, How to Size Artificial Turf: 15 ft rolls cut to any length, strips by width, 10% waste factor, pieces facing the same way.
  4. [T4] Elite Artificial Grass, How to measure square footage: rolls 15 ft wide, cut to length only, always round up.
  5. [T5] Synthetic Grass Store, Installation instructions: waste around 20% on most projects, base at least 2 in, 1.5 to 2.0 lb of silica sand per sq ft, fibers the same direction at seams.
  6. [T6] The Motz Group, How much artificial turf infill do you need per square foot: silica sand about 2 to 3 lb per sq ft, coated landscape infill 2.5 to 3.5 lb.
  7. [T7] Greatmats, Artificial turf infill and how to use it: about 2.5 to 3.5 lb of infill per sq ft.
  8. [T8] Turf & Ivy, Artificial grass installation guide: base of drain rock plus road base or DG, a 100 lb bag of infill covers about 60 sq ft, do not overlap seams, one yard of base covers 80 sq ft at 4 in.
  9. [T9] SiteOne Landscape Supply, How to install synthetic turf: excavate about 4 in, about 3 in of base, blades facing the same direction.
  10. [T10] Turf Distributors, Install guide (PDF): remove 4 in, 3 in of class 2 road base, compact, blade direction the same at seams.
  11. [NIST] NIST SP 811 Appendix B.8: 1 ft = 0.3048 m and 1 lb = 0.45359237 kg exactly.

Limits: the layout handles one rectangle at a time and assumes each strip can be as long as needed, so check your supplier's maximum roll length; a longer run needs an end seam, which is not planned here. It does not plan cut-outs around beds or trees (use total area with a waste allowance). The 1.4 tons per cu yd base density and the 0% compaction allowance are planning defaults, not measured values: compacted base needs more loose material, so ask your supplier. The input limits (lengths up to 1,000 ft, roll widths 3 to 20 ft, seam trim up to 12 in) are set by this calculator, not by a standard. Follow your turf manufacturer's infill and base instructions.

Artificial Turf Calculator FAQ

How much artificial turf do I need for my lawn?

Turf comes in rolls of a fixed width, usually 15 ft and sometimes 12 ft, cut to length. Count the strips needed to cover the width, round each strip length up to a whole foot, and multiply strips x roll width x strip length. A 30 x 20 ft lawn needs 2 strips of 15 ft turf cut 30 ft long: 900 sq ft to order, 50.0% more than the lawn itself.

Why does the calculator order more turf than my lawn area?

You buy whole strips, and each seam loses the edge trim, 3 in by default. On a 40 x 30 ft lawn, 2 strips of 15 ft are exactly 30 ft wide with nothing left for the trim, so strips running along the 40 ft side would need 3 strips and 1,800 sq ft. Running them along the 30 ft side instead takes 3 strips cut 30 ft long: 1,350 sq ft, 12.5% more than the lawn, so the calculator picks that. If your installer butts factory edges, set the seam trim to 0; the same lawn then needs 2 strips and 1,200 sq ft.

Which way should the turf strips run?

The calculator works out both directions and picks the one that needs less turf; if they tie, it picks the shorter seam. For a 30 x 20 ft lawn both directions need 900 sq ft, but strips along the 30 ft length give 30.0 ft of seam instead of 40.0 ft. Whichever way they run, lay every piece with the blades facing the same direction.

How much seam tape do I need?

Seam tape runs the full length of every seam, so buy the seam length the calculator shows: the number of seams (strips minus 1) times the length of the lawn side the strips run along. The 2 strips on a 30 x 20 ft lawn make one seam of 30.0 ft.

How much infill do I need for artificial turf?

Multiply the lawn area by the infill rate. The default is 2.0 lb per sq ft of silica sand, with a 3.0 lb preset for coated sand. A 30 x 20 ft lawn takes 1,200 lb of silica sand, or 24 bags of 50 lb; at 3.0 lb it takes 1,800 lb, or 36 bags. Use your turf maker's rate if it gives one, because some products call for much more.

How much base gravel goes under artificial turf?

A compacted base of crushed stone, decomposed granite or road base about 3 in deep is common; use 4 in where the ground freezes. For a 30 x 20 ft lawn, 3 in of base is 5.56 cu yd, about 7.78 tons at the default 1.4 tons per cu yd. That default is a planning figure that orders a little more than installer rules of thumb, so enter your supplier's density if you have one. Dig about 1 in deeper than the base, 4 in in total, which removes 7.41 cu yd of soil.

What if my lawn is not a rectangle?

Switch to total area and enter the square footage. The calculator adds a waste allowance, 10% by default or 20% for complex shapes, so 1,000 sq ft becomes 1,100 sq ft of turf to order. Area mode does not plan strips or seams; for seam planning, split the lawn into rectangles and use the rectangle layout for each one.

How we built this calculator: strips are counted across the roll width with a seam trim, strip lengths are rounded up to whole feet, and both run directions are compared. Infill and base use the lawn area with the rates shown. Roll widths, infill rates and base depths come from the turf installation guides listed above. It is a planning estimate: follow your turf manufacturer's instructions and confirm quantities with your supplier. Written and checked by the YardsCalculator editorial team.