Driveways & Paving

Asphalt Millings Calculator

Work out how many tons of asphalt millings (RAP, loose and unbound) to order, and how many loose cubic yards will arrive, for a finished compacted depth you choose. Paving with hot-mix asphalt instead? Use the asphalt calculator.

Quick answer: Tons = area × finished depth × compacted density, using about 1.66 tons per compacted cubic yard (Nebraska DOT planning figure); your supplier's figure is better. Loose cubic yards delivered = tons ÷ loose density (about 1.43 tons per cubic yard stockpiled).

Loose load vs finished layer

Loose (delivered) Finished (rolled) Finished depth (D) Same tons, less volume once compacted

Asphalt Millings Tons & Yards Calculator

Enter the area and the finished depth. Results update as you type.

Length and width

For 10 ft 6 in, enter 10.5. Up to 5,000 ft each.

Enter the finished, compacted depth. No depth is filled in for you: ask your supplier or contractor what suits your site. Up to 24 in.

Tons to order — —
Loose yards delivered—
Compacted in place—
Compaction allowance—
Loose volume, metric
—
Compacted volume, other units
—
Coverage
—
Values used
—
Formula
—

Round up when ordering; ask about the supplier's minimum. Planning estimate: your supplier's weights are the better guide.

Densities, allowance & extra

Compacted RAP: about 1.35 to 1.71 t/yd³ in DOT and FHWA data; ask your supplier. 1.66 t/yd³ (123 lb/ft³) is the Nebraska DOT in-place figure. Accepted: 0.8 to 2.5 t/yd³.

Loose or stockpiled: about 1.13 to 1.45 t/yd³. 1.43 t/yd³ is the Nebraska DOT stockpiled figure. It must not be higher than the compacted density. Not used while an allowance is entered. Accepted: 0.5 to 2.5 t/yd³.

Leave blank to work it out from the two densities. Freshly dumped millings can need 35 to 46% more volume than the finished layer (WisDOT lab loose state); a settled stockpile about 16% (Nebraska DOT). An allowance replaces the loose density and changes loose yards only, never tons. Accepted: 0 to 100.

Optional extra for edges and spillage, added to tons and loose yards. Leave blank or 0 for none. Accepted: 0 to 50.

How the calculator works

Millings are bought by weight and delivered loose, then spread and rolled to a thinner finished layer. Weight does not change when the material is compacted, so the calculator works out the tons from the finished layer and then the loose volume those tons take up on the truck.

Tons = area × D ÷ 324 × compacted density · Loose yd³ = tons ÷ loose density area in sq ft; finished (compacted) depth D in inches; densities in tons per cubic yard
  1. Compacted volume: area × finished depth ÷ 12 = cubic feet; ÷ 27 = cubic yards in place (area × D ÷ 324).
  2. Tons: compacted cubic yards × compacted density (1.66 t/yd³ by default), plus any extra you add for edges and spillage.
  3. Loose cubic yards: tons ÷ loose density (1.43 t/yd³ by default). If you enter a compaction allowance instead, the loose density becomes compacted density ÷ (1 + allowance).
  4. Compaction allowance: compacted density ÷ loose density − 1, shown as a percentage. It explains why the yards delivered are more than the yards in place. It is never added to the tons, because that would count the same material twice.

Worked example: a 40 × 12 ft area

The 4 in finished depth here is only for the arithmetic; it is not a recommendation.

  • Area: 40 × 12 = 480 sq ft.
  • Compacted volume: 480 × 4 ÷ 324 = 5.93 cu yd (160 cu ft).
  • Tons: 5.93 × 1.66 = 9.84 tons (8.92 metric tonnes).
  • Loose yards delivered: 9.84 ÷ 1.43 = 6.88 cu yd, a compaction allowance of 16%.
  • With the WisDOT lab range (1.64 t/yd³ at 35% to 1.71 t/yd³ at 46%) the same job is 9.72 to 10.13 tons and 8.00 to 8.65 loose cu yd.

Hot-mix asphalt is a dense mix placed hot, and the asphalt calculator figures it at about 2 tons per cubic yard, so the same area and depth comes to 11.85 tons there; loose millings compact to about 1.66.

Published weights for millings and RAP

Loose and compacted figures differ, and so do sources. Use your supplier's figure when you have one.

SourceStateTons per cu ydLb per cu ft
Nebraska DOTCompacted in place1.66123
Nebraska DOTStockpiled1.43106
WisDOT report WHRP G22-05 (RAP base)Compacted1.64 to 1.71121 to 127
FHWA-RD-97-148 (RAP)Compacted1.35 to 1.69100 to 125
NYC Office of Environmental Remediation (milled RAP)Not stated1.62 to 1.89120 to 140
Bulk supplier product pageLoose, as sold1.45107

"Loose" is not one state. WisDOT measured the loosest state in a lab box, Nebraska DOT a settled stockpile, and a freshly dumped truck load sits somewhere between. That is why the allowance ranges from about 16% to 35 to 46%, and why the calculator shows the allowance it used rather than one exact figure.

Before you order

  • Enter the finished, compacted depth you plan to build, not the loose depth you spread.
  • Compact thick layers in lifts. Montana DEQ limits each compacted lift to 8 in when millings are reused as base, and the calculator shows a note above 8 in.
  • Ask your supplier how they sell millings (by the ton or by the yard) and what weight per yard they use, then enter it.
  • Round up when ordering; ask about the supplier's minimum. The calculator does not round to whole tons or truckloads, because minimums vary.

Asphalt Millings FAQ

How much does a cubic yard of asphalt millings weigh?

It depends on whether the millings are loose or compacted. Nebraska DOT uses 1.66 tons per cubic yard (123 lb per cubic foot) for millings compacted in place and 1.43 tons per cubic yard for stockpiled material. Published figures for compacted RAP run from about 1.35 to 1.71 tons per cubic yard, so your supplier's figure is the better guide.

How much extra volume do I need for compaction?

Loose millings take up more room than the finished, rolled layer. The Nebraska DOT figures imply about 16% more volume from a settled stockpile to the finished layer, and WisDOT lab tests on RAP base found 35 to 46% from the loosest state. The weight does not change when millings are compacted, so the allowance changes the loose cubic yards, not the tons.

How deep should I spread asphalt millings?

This calculator does not recommend a depth. We did not find an authoritative source for driveway depth, so enter the finished, compacted depth you plan to build and ask your supplier or contractor what suits your site. Thick layers should be compacted in lifts; Montana DEQ limits each compacted lift to 8 in when millings are reused as base.

Is this the same as the asphalt calculator?

No. The asphalt calculator is for hot-mix asphalt, a dense mix placed hot, which it figures at about 2 tons per cubic yard. This calculator is for loose millings that are spread and rolled like gravel. For a 40 by 12 ft area at 4 in finished depth, it gives 9.84 tons of millings, against 11.85 tons of hot mix on the asphalt calculator.

Sources and limits

Sources accessed November 13, 2026. Limits: this is a planning estimate for an even layer of one depth. It gives no price and no recommended depth. Weights vary with the source pavement, gradation and moisture, and scale tickets weigh the material as delivered. The input limits (length and width up to 5,000 ft, area up to 1,000,000 sq ft, depth up to 24 in, compacted density 0.8 to 2.5 t/yd³, loose density 0.5 to 2.5 t/yd³, allowance 0 to 100%, extra 0 to 50%) are limits set by this calculator, not by a standard.

How we built this calculator: tons = area × finished depth × compacted density, with default densities of 1.66 t/yd³ compacted and 1.43 t/yd³ stockpiled from Nebraska DOT, checked against WisDOT, FHWA and NYC figures. Loose cubic yards = tons ÷ loose density, and the compaction allowance is worked out from the two densities. It is a planning estimate: your supplier's weights are the better guide. Written and checked by the YardsCalculator editorial team.