Concrete Weight
Volume × density · results update as you type
Your result (placed, fresh weight; planning estimate)
Find out how much a concrete slab or a volume of concrete weighs. Enter the length, width and thickness, or a volume, and get the weight in pounds, short tons and kilograms.
Placed (fresh) normal-weight concrete weighs about 4,000 lb per cubic yard (2 short tons) as a planning value. The typical range is 140 to 150 lb per cubic foot, which is 3,780 to 4,050 lb per cubic yard.
Example: a 10 x 10 ft slab that is 4 in thick holds 1.23 cu yd and weighs about 4,940 lb (2.47 short tons).
Volume × density · results update as you type
Your result (placed, fresh weight; planning estimate)
Weight (lb) = volume (cu ft) × density (lb per cu ft)
With the planning value of 4,000 lb per cubic yard, weight (lb) = cubic yards × 4,000. Short tons = pounds ÷ 2,000, and kilograms = pounds × 0.45359237.
Assumptions: even thickness, no waste or spillage, and a density that is a planning value rather than a measured one. The result is the weight of the concrete as placed (fresh), not an allowance for formwork, base material or anything else on the job.
For a slab, the weight per square foot is simply thickness in feet × density: 4 in is 1/3 ft, so 49.4 lb per sq ft, and 6 in gives 74.1 lb per sq ft.
Each row uses 4,000 lb per cubic yard. Pounds are rounded to the nearest 10 above 1,000 lb because the real density varies by several percent.
| Slab | Volume | Weight (lb) | Short tons | Kilograms | lb per sq ft |
|---|---|---|---|---|---|
| 10 x 10 ft, 4 in thick | 1.23 cu yd | 4,940 | 2.47 | 2,240 | 49.4 |
| 10 x 10 ft, 6 in thick | 1.85 cu yd | 7,410 | 3.70 | 3,360 | 74.1 |
| 12 x 12 ft, 4 in thick | 1.78 cu yd | 7,110 | 3.56 | 3,230 | 49.4 |
| 20 x 20 ft, 4 in thick | 4.94 cu yd | 19,750 | 9.88 | 8,960 | 49.4 |
| 20 x 20 ft, 6 in thick | 7.41 cu yd | 29,630 | 14.81 | 13,440 | 74.1 |
Doubling the area doubles the weight, and a 6 in slab weighs 1.5 times a 4 in slab of the same size.
Two published sources put normal-weight concrete at 140 to 150 lb per cubic foot. This calculator uses 4,000 lb per cubic yard as a single planning value inside that range, and shows the range next to every result. Neither source names one exact figure, so 4,000 is a planning choice, not a quotation.
| Density | lb per cu ft | lb per cu yd | Short tons per cu yd | kg per m³ |
|---|---|---|---|---|
| Low end of range | 140 | 3,780 | 1.89 | 2,243 |
| Planning value | 148.15 | 4,000 | 2.00 | 2,373 |
| High end of range | 150 | 4,050 | 2.03 | 2,403 |
Air content, aggregate and mix design move the real figure inside, or outside, that range. The sources describe fresh, typical normal-weight concrete. If your supplier gives a density for your mix, choose “Custom density” and enter it.
Do not find the weight of a pour by multiplying the number of bags by the bag weight. An 80 lb bag of dry mix yields about 0.60 cubic feet (QUIKRETE Concrete Mix 1101 data sheet), so the dry mix is about 133 lb per cubic foot. Once water is added, placed concrete is typically 140 to 150 lb per cubic foot (see the sources below).
One cubic yard (27 cu ft) is about 45 bags of 80 lb, or 3,600 lb of dry mix, while the placed concrete weighs about 4,000 lb. To order bags for a job, use the concrete bag calculator (40, 50, 60, 80 and 90 lb bags) or the concrete calculator (bags with a waste allowance).
Need the volume or the number of yards to order for a pour? Use the concrete slab calculator or the cubic yard calculator. For other materials, see the yards to tons calculator.
Limits: the sourced figures are for typical normal-weight concrete. Lightweight or heavyweight mixes are outside the planning value, so enter a custom density for them. The accepted custom density (50 to 200 lb per cubic foot) and the largest allowed size (10,000 ft length, 120 in thickness, 1,000,000 cu yd) are limits set by this calculator, not by a standard.
About 4,000 pounds (2 short tons) as a planning value. Normal-weight concrete is typically 140 to 150 pounds per cubic foot, which is 3,780 to 4,050 pounds per cubic yard.
About 148 pounds on this page's planning value (4,000 lb per cubic yard divided by 27). The typical range is 140 to 150 pounds per cubic foot.
It holds about 1.23 cubic yards, which is roughly 4,940 pounds (2.47 short tons or 2,240 kg) at 4,000 lb per cubic yard. At the 140 and 150 lb per cubic foot ends of the range it is about 4,670 to 5,000 pounds.
About 49 pounds per square foot at the planning density (4 inches is 1/3 foot, times 148.15 lb per cubic foot is 49.4). A 6 inch slab is about 74 pounds per square foot.
No. An 80 lb bag of dry mix makes about 0.60 cubic feet (QUIKRETE data sheet), and once water is added, placed concrete is typically 140 to 150 pounds per cubic foot (see the sources). One cubic yard is about 45 bags of 80 lb.
No. It is a planning value inside the typical 140 to 150 lb per cubic foot range. Mix design, air content and aggregate change the real figure, so use your supplier's number or enter a custom density when you have one.
How we built this calculator: weight = volume × density, with a planning density of 4,000 lb per cubic yard (148.15 lb per cubic foot) inside the sourced 140 to 150 lb per cubic foot range. It is a planning estimate of placed (fresh) weight: confirm with your supplier. Written and checked by the YardsCalculator editorial team.
Sources: Iowa DOT IM 340, NRMCA CIP 36, QUIKRETE 1101. 1 foot = 0.3048 m exactly and 1 inch = 2.54 cm exactly (NIST SP 811 Appendix B.8, accessed November 11, 2026).
Last updated: November 11, 2026