Landscaping

Dry Well Calculator

Quick answer: 1 in of rain on 1,000 sq ft of roof is about 623 gallons (area × rain ÷ 12 × 7.48). A 4 × 4 × 3 ft pit filled with washed stone holds about 144 gallons, because only about 40% of a stone-filled pit is open space for water. That is 23% of the storm; holding all of it takes about 208.3 cu ft of stone-filled pit, for example 8.3 ft square and 3 ft deep.

Size a dry well for a downspout, roof or paved area from one set of inputs: the runoff from a design storm in gallons, how much your stone-filled pit (with or without a plastic chamber or perforated barrel) can store, the pit size needed to hold the whole storm, and the washed stone to order in cubic yards and tons.

Dry well cross-section

Grade From downspout Chamber Stone Width (W) or diameter Depth (D)

Dry Well Size & Stone Calculator

Enter the area that drains to the well, the storm, and the pit size. Results update as you type.

The roof or paved area that drains to this well, measured flat (its footprint). Up to 1,000,000 sq ft.

The storm you want the well to hold. 1 in is a common homeowner design storm; your local code may set a different one.

Rectangular pit size

Depth of the stone-filled part. Homeowner dry wells are typically about 3 ft deep. Each size up to 100 ft.

Use the storage volume printed by the chamber maker. The chamber is assumed to be thin-walled, so the space it takes equals the water it holds.

Share of the storm the pit holds —

—

Runoff—
Pit storage—
Washed stone to order—
Pit volume
—
Stone-filled volume
—
Chamber or barrel
—
Pit needed to hold the full storm
—
That pit at your depth
—
Metric
—
Values used
—
Formula
—

Planning estimate; check soil percolation and local code. Stone includes the extra % below; storage never does.

Stone, voids & runoff

Share of the stone-filled space that holds water. 0.40 (40%) is the common design value; you can also type 40 for 40%. Accepted: 0.10 to 0.50.

1.0 means all the rain reaches the well (the safe choice for a roof). A lower value is your own assumption. Accepted: 0.1 to 1.0.

1.40 for washed #57, the same value as our French drain calculator. Use your supplier's figure if you have one. Accepted: 0.5 to 2.5.

Added to the stone order only, for settling and uneven pit walls. Leave blank for 10%; enter 0 for none. Accepted: 0 to 50.

How to size a dry well

A dry well is a pit filled with clean, washed stone (sometimes around a plastic chamber or a perforated barrel) that takes water from a downspout or a French drain and lets it soak into the ground. The stone itself takes up most of the pit, so only the gaps between stones store water. Sizing is a comparison of two volumes: the water a storm sends to the well, and the water the pit can hold.

Storage = (pit − chamber) × void ratio + chamber all volumes in cubic feet; × 7.48 for gallons (1 cu ft = 1728 ÷ 231 gal)
  1. Runoff: drainage area (sq ft) × rainfall (in) ÷ 12 × runoff coefficient = cubic feet. Multiply by 7.48 for gallons.
  2. Pit volume: length × width × depth, or 3.1416 × diameter² ÷ 4 × depth for a round pit.
  3. Stone volume: pit volume minus the chamber, because stone fills only the space the chamber does not.
  4. Storage: stone volume × void ratio (0.40), plus the chamber's own storage.
  5. Compare: storage ÷ runoff is the share of the storm the pit holds. If it is short, the pit needed is (runoff − chamber) ÷ void ratio + chamber.
  6. Order stone: stone volume ÷ 27 for cubic yards, add 10% extra, then × 1.40 tons per cubic yard.

Worked example: one downspout from a 1,000 sq ft roof

A 1 in storm on 1,000 sq ft of roof, draining to a 4 × 4 × 3 ft pit of washed stone with no chamber.

  • Runoff: 1,000 × 1 ÷ 12 = 83.3 cu ft × 7.48 = 623 gal
  • Pit: 4 × 4 × 3 = 48.0 cu ft; storage: 48.0 × 0.40 = 19.2 cu ft = 144 gal
  • Holds 144 ÷ 623 = 23% of the storm, short by 480 gal
  • Pit for the full storm: 83.3 ÷ 0.40 = 208.3 cu ft, or 69.4 sq ft at 3 ft deep (about 8.3 ft square or 9.4 ft round)
  • Stone for the 4 × 4 × 3 ft pit: 48.0 ÷ 27 = 1.78 cu yd, +10% = 1.96 cu yd × 1.40 = 2.74 tons

Add a 50 gal chamber to the same pit and storage rises to 23.2 cu ft (174 gal, 28%), while the stone order falls to 1.68 cu yd (2.36 tons), because the chamber holds all of its volume as water instead of 40%.

What the model leaves out: water soaking into the soil during the storm (ignoring it errs on the safe side), water ponding above the stone, and freezing. It sizes storage for one storm; it does not say how fast the well drains.

Runoff from 1 inch of rain

All rain reaching the well (runoff coefficient 1.0). Double the gallons for a 2 in storm.

Runoff volume in cubic feet, gallons and liters from 1 inch of rain by drainage area
Drainage areaCubic feetGallonsLiters
500 sq ft41.73121,180
1,000 sq ft83.36232,360
1,500 sq ft125.09353,540
2,000 sq ft166.71,2474,719
2,500 sq ft208.31,5585,899
3,000 sq ft250.01,8707,079

How much water a stone-filled pit holds

Stone only, no chamber, 0.40 void ratio. Stone order includes 10% extra at 1.40 tons per cubic yard.

Pit volume, water storage and washed stone needed for common dry well sizes
Pit sizePit cu ftStorage cu ftStorage galStone cu ydStone tons
3 × 3 × 3 ft27.010.8811.101.54
4 × 4 × 3 ft48.019.21441.962.74
4 × 4 × 4 ft64.025.61922.613.65
5 × 5 × 4 ft100.040.02994.075.70
6 × 6 × 4 ft144.057.64315.878.21
Round, 3 ft across × 4 ft28.311.3851.151.61
Round, 4 ft across × 4 ft50.320.11502.052.87
Round, 6 ft across × 4 ft113.145.23384.616.45

With the conservative 0.36 void ratio, the 4 × 4 × 3 ft pit holds 17.3 cu ft (129 gal), and holding 1 in on 1,000 sq ft needs 231.5 cu ft of pit.

Dry well tips and common mistakes

  • Do not count the whole pit as storage. About 40% of a stone-filled pit holds water; the stone takes the rest. Some designers use 36% to be safe.
  • Do not count the chamber twice. Stone fills only the space around a chamber, so subtract the chamber before applying the void ratio, then add the chamber back.
  • Use clean, washed stone. AASHTO No. 57, or 1/2 to 1 1/2 in crushed stone, keeps open voids; the Minnesota Stormwater Manual specifies 1.5 to 3 in uniform stone. Stone with fines fills the gaps and leaves less room for water.
  • Check the soil and the rules first. A dry well only works where water can soak in. Check soil percolation and local code for where a dry well may go and whether it needs a permit.
  • Call 811 before you dig. Ask for a utility locate before digging the pit.
  • Feed it from a French drain or downspout. A French drain can carry water across the yard and end at the dry well.

Dry well FAQ

How big should a dry well be?

Big enough to hold the runoff from your design storm. Work out the runoff (area in square feet x rainfall in inches / 12, times 7.48 for gallons), then divide the runoff in cubic feet by the void ratio, 0.40 for washed stone. For 1 in of rain on 1,000 sq ft that is 83.3 / 0.40 = 208.3 cubic feet of stone-filled pit, for example about 8.3 ft square and 3 ft deep.

How many gallons does a dry well hold?

A stone-filled pit holds its volume x the void ratio. At 0.40, a 4 x 4 x 3 ft pit (48 cubic feet) holds 19.2 cubic feet, about 144 gallons. A plastic chamber adds its full storage, and the stone around it holds 40% of the space that is left.

How much water comes off my roof in a storm?

Multiply the roof footprint in square feet by the rainfall in inches, divide by 12 for cubic feet, and multiply by 7.48 for gallons. 1 in of rain on 1,000 sq ft of roof is about 623 gallons.

What void ratio should I use for dry well stone?

0.40 (40%) is the value used by the Minnesota Stormwater Manual, the Philadelphia Water Department and the NH LAKES dry well guide for clean, uniform stone. Some designers use 0.36 to be safe, which this calculator offers as the conservative option.

How much gravel do I need for a dry well?

Use clean, washed stone such as #57 gravel. Take the pit volume, subtract any chamber, divide by 27 for cubic yards and add about 10% for settling. A 4 x 4 x 3 ft pit with no chamber needs about 1.96 cubic yards, or 2.74 tons of washed stone at 1.40 tons per cubic yard.

Is a dry well the same as a French drain?

No. A French drain is a gravel-filled trench with a pipe that moves water away along its length. A dry well is a pit that stores water so it can soak into the ground, and a French drain or downspout often ends at one. Use the French drain calculator for the trench and this calculator for the pit.

Sources and limits

Sources accessed November 13, 2026. Limits: this is a planning estimate of storage volume for one storm. It does not size a dry well for your soil, drain-down time, frost or local rules, and it is not an engineering design. The input limits (area up to 1,000,000 sq ft, rain up to 24 in, sizes up to 100 ft, chamber up to 100,000 gal, void ratio 0.10 to 0.50, density 0.5 to 2.5) are limits set by this calculator, not by a standard.

How we built this calculator: runoff = area × rain ÷ 12 × coefficient, storage = (pit − chamber) × void ratio + chamber, with a 0.40 void ratio from public stormwater manuals and the same 1.40 tons per cubic yard stone density as our French drain calculator. It is a planning estimate: check soil percolation and local code. Written and checked by the YardsCalculator editorial team.