Conversion Calculator

Linear Feet to Square Feet Calculator

Convert linear feet to square feet, or square feet to linear feet, on one page. Pick the direction, enter the width of the board, roll, strip or fence, and get the answer in feet and meters.

Quick answer

You need a width to convert linear feet to square feet, because a linear foot is length only. Square feet = linear feet × width in feet. To go back: linear feet = square feet ÷ width in feet.

Example: 100 linear feet of 6 inch wide board = 100 × 0.5 = 50 sq ft.

Linear Feet ↔ Square Feet

Length × width · results update as you type

Convert

Required, no default. Check the unit: 6 in is 0.5 ft, not 6 ft. Your width in feet is shown in the results.

Default 0%. Add an allowance only if you are buying material; confirm with your supplier.

Boards (actual width):
Rolls:
Fence height:
Edging strip:

Your result

Square Feet —
Square Meters—
Formula—

Linear Feet to Square Feet Formula

Square feet = linear feet × width in feet

Linear feet = square feet ÷ width in feet

Convert the width to feet first: inches ÷ 12, centimeters ÷ 30.48, meters ÷ 0.3048. In metric, square meters = meters × width in meters.

Why a width is required

A linear foot is a length of one foot along a board, roll, pipe or fence line. It has no width, so it has no area. The same 100 linear feet is 25 sq ft of 3 inch strip but 100 sq ft of 12 inch strip.

Step by step

  1. Measure the length (or area) and the width of the strip, board, roll or fence height.
  2. Turn the width into feet. A 6 inch width is 6 ÷ 12 = 0.5 ft.
  3. To get area, multiply length by width. To get length, divide area by width.
  4. If you are buying material, add a waste allowance and round up.

Assumptions: constant width, boards butt together with no gap, one face only, no waste unless you enter it. Gaps between boards, saw cuts and trimming all change how much you must buy.

Do not confuse these

Worked Examples

Each line uses the formulas above. Results are before gaps and waste.

JobWidthCalculationResultMetric
Decking: 150 sq ft needs how many linear feet of boards5.5 in = 0.4583 ft150 ÷ 0.4583327.3 linear ft99.8 m
Weed barrier: 100 sq ft from a roll3 ft100 ÷ 333.3 linear ft10.2 m
Fence: 20 linear ft, area of one face to stain6 ft (height)20 × 6120.0 sq ft11.1 m²
Edging strip: 50 linear ft4 in = 0.3333 ft50 × 0.333316.7 sq ft1.5 m²
Reverse: 80 sq ft of boards6 in = 0.5 ft80 ÷ 0.5160.0 linear ft48.8 m

Linear Feet in One Square Foot, by Width

Linear feet per square foot = 1 ÷ width in feet.

WidthLinear feet per sq ftSq ft per 100 linear ft
1 in12.008.3
3.5 in3.4329.2
5.5 in2.1845.8
6 in2.0050.0
12 in1.00100.0

About the Width Presets

The preset buttons only fill in the width; you can edit it. Board presets use the finished (dressed) width, not the nominal name: a 2x4 is about 3.5 inches wide and a 2x6 about 5.5 inches, while a 2x8 is about 7.25 inches. Actual sizes vary by product and mill, so check the label. Roll widths are generic examples, so enter the width printed on your roll.

Common Mistakes

  • Using inches as feet. A 6 inch width is 0.5 ft. Entering 6 as feet gives 12 times too much area.
  • Using the nominal board size. A “2x6” face is not 6 inches wide.
  • Ignoring gaps and waste. Deck boards are usually spaced and cut to length, so buy more than the figure shown.
  • Mixing up related conversions. For a rectangle of length × width in feet, use the square footage calculator or floor area calculator.

Planning a deck or fence? See the deck calculator and fence calculator.

Linear Feet to Square Feet FAQ

How do you convert linear feet to square feet?

Multiply the linear feet by the width in feet. Square feet = linear feet x width (ft). A width is required because a linear foot measures length only. If the width is in inches, divide it by 12 first.

How many linear feet are in a square foot?

It depends on the width: linear feet per square foot = 1 / width in feet. That is 12 for a 1 inch wide strip, 2 for a 6 inch wide strip and 1 for a 12 inch wide strip.

How do I convert square feet to linear feet?

Divide the area in square feet by the width in feet. Linear feet = square feet / width (ft). For example, 80 sq ft of 6 inch (0.5 ft) boards is 160 linear feet.

How many linear feet of 5.5 inch decking boards cover 100 square feet?

5.5 inches is 0.4583 ft, so 100 / 0.4583 = 218.2 linear feet before gaps and waste.

Is a linear foot the same as a foot?

For length, yes: a linear foot is one foot measured along the length of a strip, board, roll or run. The term signals that width is not included.

Is a linear foot the same as a board foot?

No. A board foot is a volume (12 x 12 x 1 inch). Use the board foot calculator for volume.

How we built this calculator: square feet = linear feet × width in feet, and linear feet = square feet ÷ width in feet, with an optional waste percentage applied once to the result. It is a planning estimate: confirm quantities with your supplier. Written and checked by the YardsCalculator editorial team.