Landscaping

Polymeric Sand Calculator

Quick answer: Bags = joint volume × sand density × 1.10 ÷ bag weight. For 200 ft² of 4 × 8 in pavers with 1/8 in joints, that is about 1.70 ft³ of joint space and 4 bags of 50 lb.

Work out how many bags of polymeric sand fill the joints of your patio, walkway or driveway from the paver size, the joint width and the joint depth, instead of a flat rule of thumb. You get the joint volume, the pounds of sand, the bags to buy and the equivalent coverage per bag, so you can compare it with the coverage printed on your bag.

Paver joint cross-section

Bedding sand and base (not counted) Paver Paver Joint width (j) Thickness (T) d 1/8 in

Polymeric Sand Bags Calculator

Enter the paved area, the paver size and the joint width. Results update as you type.

Length × width of the paved surface. A 10 × 20 ft patio is 200 sq ft. Up to 100,000 sq ft.

Paver size

For mixed sizes, enter the average length and width. Up to 48 in each.

2.375 in (2-3/8 in) is a common patio paver; driveway pavers are often 3.125 in (80 mm). Up to 6 in.

The gap between pavers. Type a decimal (1/8 in = 0.125) or tap a size. Accepted: 1/32 to 4 in.

Leave blank for auto: paver thickness minus 1/8 in = 2.25 in. Type a depth to override; it cannot be more than the paver thickness.

Bags to buy — —
Joint volume—
Sand weight—
Equivalent coverage—
Joint volume, other units
—
Sand to order
—
Joints take up
—
Values used
—
Formula
—

Compare with the coverage on your bag; labels list about 25-120 ft² for narrow joints and 15-42 ft² for wide joints. Planning estimate; follow the product label.

Sand, bag size & extra

106 lb/ft³ is the figure Sika prints for its Evolution polymeric sands. Other brands may differ: check your bag. Accepted: 60 to 150 lb/ft³ (961 to 2,403 kg/m³).

50 lb bags are the most common; some products come in 40 lb buckets. Accepted: 1 to 100 lb.

Added to the pounds and bags only, never to the joint volume or coverage. 10% is our planning choice, not a manufacturer figure. Leave blank for 10%; enter 0 for none. Accepted: 0 to 50.

How the calculator works

Polymeric sand fills only the joints between pavers, so the amount you need depends on how much of the patio is joint and how deep you fill it. Every manufacturer we checked says coverage depends on the paver size, the joint width and the depth, which is why this calculator starts from those three things.

Joint volume = area × (1 − L × W ÷ ((L + j) × (W + j))) × d ÷ 12 area in sq ft; paver length L, width W, joint width j and joint depth d in inches; result in cubic feet
  1. Joint share: each paver plus its share of the joints covers (L + j) × (W + j). The part that is not paver, 1 − L × W ÷ ((L + j) × (W + j)), is the share of the patio that is joint. This is the same for stack bond, running bond and herringbone patterns.
  2. Joint depth: paver thickness minus 1/8 in, because the sand is filled to about 1/8 in below the surface. You can type your own depth instead.
  3. Joint volume: area × joint share × depth ÷ 12 = cubic feet.
  4. Sand weight: cubic feet × density (106 lb/ft³ by default) = pounds.
  5. Bags: pounds plus 10% extra, divided by the bag weight, rounded up to a whole bag.
  6. Equivalent coverage: area ÷ (pounds ÷ bag weight) = sq ft per bag before the extra, the same kind of number printed on the bag.

Bedding sand is not included. Only the joints between pavers are counted; the screeded layer under the pavers is on the paver base calculator and the sand calculator.

Worked example: a 200 sq ft patio of 4 × 8 in pavers

4 × 8 in pavers, 2-3/8 in thick, with 1/8 in joints on a 200 sq ft patio.

  • Each paver plus its joints covers 4.125 × 8.125 = 33.52 sq in, of which 32 sq in is paver, so joints are 4.5% of the patio.
  • Joint depth: 2-3/8 − 1/8 = 2.25 in.
  • Joint volume: 200 × 0.0452 × 2.25 ÷ 12 = 1.70 cu ft, about 180 lb of sand at 106 lb/ft³.
  • With 10% extra that is 198 lb, so 4 bags of 50 lb.
  • Equivalent coverage: 200 ÷ (180 ÷ 50) = 55.6 sq ft per bag, inside the 25 to 120 sq ft that labels list for narrow joints.

Bag coverage by joint width

Coverage printed by four manufacturers for a 50 lb bag. Each one says coverage varies with paver size, joint width and depth.

Product (50 lb bag)Narrow jointsWide joints
SEK Surebond PolySweep50-75 sq ft (up to 1/4 in); 25-50 sq ft (1/4 to 1/2 in)15-25 sq ft (1/2 to 3/4 in)
Alliance Gator Maxx G2 / Supersand G2 (2-3/8 in pavers)65-85 sq ft (1/8 to 3/8 in)22-42 sq ft (3/4 to 1-1/4 in)
Techniseal SmartSand60-120 sq ft25-40 sq ft
Sika Evolution60-90 sq ft20-40 sq ft

Across these products a 50 lb bag covers roughly 25 to 120 sq ft on narrow joints and 15 to 42 sq ft on wide joints. Products are also rated for different joint widths, from 1/16 in up to 1 in for some and up to 2 or 4 in for wide-joint products, so check the bag.

This calculator's coverage for common pavers

Sq ft per 50 lb bag at 106 lb/ft³, 2-3/8 in pavers filled to 1/8 in below the top, before the extra.

Paver1/8 in joint1/4 in3/8 in3/4 in1 in
4 × 8 in55.628.819.910.98.7
6 × 9 in74.438.126.114.011.0
12 × 12 in122.662.342.122.017.0

On narrow joints these results fall inside the label ranges. On wide joints with small pavers the calculator gives less coverage than the labels (for example 10.9 sq ft per bag at 3/4 in on 4 × 8 in pavers, against 22 to 42 on the Gator chart), so there it leans toward buying more.

Why your result may differ from the bag label

  • Wide joints: on joints of about 1/2 in and wider the result is conservative. If your product's label gives a coverage for your joint width, the label is the better guide.
  • Spacer bars: Alliance Gator says pavers with large spacer bars typically use 10 to 15% less sand than a geometric calculation, because the bars fill part of the joint. This calculator does not subtract them.
  • Chamfered and tumbled edges: bevelled or rounded edges open up the top of the joint and add some sand. The calculator does not add it; the extra percentage is there for this kind of difference.
  • Mixed sizes and patterns: enter the average paver length and width. Stack bond, running bond and herringbone give the same joint share; patterns with half units are approximate.
  • Density: the default 106 lb/ft³ comes from one manufacturer, and the same data sheet also lists 1,800 kg/m³ (about 112 lb/ft³). If your bag gives a density, enter it.

Before you buy

  • Fill joints to about 1/8 in below the paver surface (or below the chamfer). Most products need at least 1.5 in of sand depth.
  • Check the joint widths the product is rated for. A sand for narrow joints may not suit 1 in joints.
  • Buy whole bags and keep a spare for refills.

Polymeric Sand FAQ

Why does joint width change how many bags I need?

The sand fills the gaps, so the space to fill grows with the joint width and shrinks as the pavers get bigger. With 4 x 8 in pavers, 1/8 in joints are 4.5% of the patio, but 1/4 in joints are 8.7%. On a 200 sq ft patio that is the difference between 4 and 8 bags of 50 lb.

How deep should polymeric sand fill the joints?

Fill the joints to about 1/8 in below the top of the pavers, or below the chamfer. Most products need at least 1.5 in of sand depth. For a 2-3/8 in paver that is a fill depth of 2.25 in, which is what the calculator uses by default.

Why is my result different from the coverage on the bag?

Bag labels give a range for typical joints, about 25 to 120 sq ft per 50 lb bag for narrow joints and 15 to 42 sq ft for wide joints, because coverage depends on paver size, joint width and depth. This calculator works from your own pavers and joints. On narrow joints it falls inside the label ranges; on wide joints with small pavers it gives less coverage than the labels, so it leans toward buying more.

Do spacer bars change how much sand I need?

Yes. Alliance Gator says pavers with large spacer bars typically use 10 to 15% less sand than its geometric calculation, because the bars fill part of the joint. This calculator does not subtract spacer bars, so its result is on the high side for those pavers.

What sand density does the calculator use?

106 lb per cubic foot, the figure Sika prints for its Evolution polymeric sands. The same data sheet also lists 1,800 kg per cubic meter, which is about 112 lb per cubic foot; the default 10% extra covers that difference. The other manufacturers we checked do not publish a density, so if your bag lists one, enter it.

Sources and limits

Sources accessed November 13, 2026. No brand is recommended over another. Limits: this is a planning estimate for rectangular pavers of one size with joints filled to an even depth. It ignores spacer bars, chamfers and sweeping losses (the extra percentage covers the last two). The input limits (area up to 100,000 sq ft, pavers up to 48 in and 6 in thick, joints 1/32 to 4 in, density 60 to 150 lb/ft³, bags 1 to 100 lb, extra 0 to 50%) are limits set by this calculator, not by a standard. Always follow the product label.

How we built this calculator: joint volume = area × joint share × depth ÷ 12, with the joint share from the paver size and joint width, a fill depth of paver thickness minus 1/8 in, and a default density of 106 lb/ft³ from a manufacturer data sheet. Bag coverage ranges come from four manufacturers' published data. It is a planning estimate: follow the product label. Written and checked by the YardsCalculator editorial team.