Volume Calculator

Stockpile Volume Calculator

Find how much material is in a pile of dirt, gravel, sand, topsoil, crushed stone or mulch. Measure a cone-shaped pile or a long rectangular pile with sloped sides, and get cubic yards, cubic feet, cubic meters, tons and 10 cubic yard truckloads.

Quick answer

A cone-shaped pile holds π × r² × h ÷ 3. A pile 20 ft across and 8 ft high is about 837.76 cu ft, or 31.03 cu yd.

As gravel at 1.4 tons per cu yd that is about 43.44 tons, or 3.1 loads of 10 cu yd (plan for 4 trips).

Pile Volume

Cone or rectangular pile · results update as you type

Cone pile dimensions

Vertical height from the ground to the top, not the length up the slope.

Planning densities from the yards to tons calculator. Moisture and product change the real figure.

Your result (loose pile volume; planning estimate)

Cubic yards —
Cubic feet—
Cubic meters—
Short tons—
Tonnes (metric)—
10 cu yd truckloads—

Stockpile Volume Formulas

Cone-shaped pile

V = π × r² × h ÷ 3

r is the radius (half the diameter) and h is the vertical height. If you measured around the bottom instead, r = circumference ÷ (2 × π).

Rectangular pile with sloped sides

V = h ÷ 6 × (A1 + A2 + 4 × Am)

A1 is the base area (base length × base width), A2 is the flat top area (top length × top width) and Am is the area halfway up: ((base length + top length) ÷ 2) × ((base width + top width) ÷ 2). This prismoidal formula is exact for a pile whose sides are straight slopes. When the top is the same shape as the base (for example a square base and a square top), it gives the same answer as the frustum formula V = h ÷ 3 × (A1 + A2 + √(A1 × A2)).

Step by step

  1. Measure in one unit (feet, inches or meters) and pick it in the calculator.
  2. Work out cubic feet with the formula for your pile shape.
  3. Divide cubic feet by 27 for cubic yards; multiply cubic feet by 0.0283168 for cubic meters.
  4. Multiply cubic yards by the density in tons per cubic yard for short tons.
  5. Divide cubic yards by 10 for the number of 10 cubic yard truckloads, and round up for trips.

Assumptions: a pile on flat ground, straight sloped sides and a single material. The result is the loose volume of the pile as it sits, not a compacted volume, and the density is a planning value rather than a measured one.

Worked Examples: Common Pile Sizes

Tons use gravel at 1.4 tons per cubic yard. Truckloads are 10 cubic yard loads.

PileCubic feetCubic yardsCubic metersTons of gravel10 cu yd loads
Cone, 10 ft across, 5 ft high130.904.853.716.790.5
Cone, 20 ft across, 8 ft high837.7631.0323.7243.443.1
Cone, 30 ft across, 10 ft high2,356.1987.2766.72122.178.7
Cone, 40 ft across, 12 ft high5,026.55186.17142.34260.6418.6
Rectangular, 20 x 20 ft base, 10 x 10 ft top, 5 ft high1,166.6743.2133.0460.494.3
Rectangular, 30 x 20 ft base, 14 x 4 ft top, 8 ft high2,282.6784.5464.64118.368.5
Rectangular, 40 x 20 ft base, 20 x 10 ft top, 6 ft high2,800.00103.7079.29145.1910.4

Doubling the height of a cone doubles its volume, but doubling the diameter makes it four times larger, so measure across the pile carefully.

Pile Volume to Tons

These are the same planning densities used on the yards to tons calculator. For the 20 ft by 8 ft cone above (31.03 cu yd):

MaterialTons per cu ydTons in a 31.03 cu yd pile
Gravel1.443.44
Crushed stone1.443.44
Sand1.3541.89
Topsoil1.340.34
Mulch0.5517.07

Wet material weighs more than dry, and products vary. If your supplier quotes a density, choose “Custom density” and enter it.

How to Measure a Pile

  • Cone: measure straight across the base through the middle, or run a tape around the bottom edge for the circumference.
  • Rectangular pile: measure the length and width at the ground, then the length and width of the flat top. The top cannot be larger than the base.
  • Height: measure the vertical height from the ground to the top, for example with a pole held upright and a level line from the peak.

Common Mistakes

  • Measuring up the slope. The slope is longer than the height, so it overstates the volume.
  • Using the radius as the diameter. Entering the half-width as the diameter gives a quarter of the real volume.
  • Treating a rectangular pile as a box. Length × width × height ignores the sloped sides and can overstate the volume by half or more.
  • Mixing up short tons and tonnes. A short ton is 2,000 lb; a metric tonne is 1,000 kg (about 2,205 lb).

Need to order material for a project instead of measuring a pile? Use the gravel calculator or the fill dirt calculator. To plan hauling, see how many yards are in a dump truck.

Sources and Limits

Limits: the formulas assume flat ground and straight sloped sides. Real piles are rarely perfect, so treat the result as an estimate and measure in several places on irregular piles. The largest accepted size (5,000 ft across or along, 500 ft high) and the custom density range (0.1 to 5 tons per cubic yard) are limits set by this calculator, not by a standard. A 10 cubic yard truckload is a planning size; real truck capacity depends on the truck and its weight limit.

Stockpile Volume FAQ

How do I calculate the volume of a cone-shaped pile?

Use V = pi x r squared x h / 3, where r is half the base diameter and h is the vertical height. A pile 20 ft across and 8 ft high holds about 837.76 cubic feet, which is 31.03 cubic yards.

What if I cannot measure across the pile?

Walk around the bottom edge and measure the circumference instead. The radius is the circumference divided by 2 x pi, so a 62.83 ft circumference is a 20 ft diameter. Choose "Circumference" in the calculator and it does this for you.

How do I measure the height of a stockpile?

Measure the vertical height from the ground at the base to the top of the pile, not the length up the slope. The slope length is always longer than the height, so using it overstates the volume.

How do I find the volume of a long pile with sloped sides?

Measure the base length and width, the flat top length and width, and the height, then use the prismoidal formula V = h / 6 x (base area + top area + 4 x middle area). A pile with a 30 x 20 ft base, a 14 x 4 ft top and 8 ft height holds about 2,282.67 cubic feet, or 84.54 cubic yards.

How many tons are in my pile?

Multiply the cubic yards by the material density in tons per cubic yard. This page uses the same planning densities as the yards to tons calculator: gravel and crushed stone 1.4, sand 1.35, topsoil 1.3 and mulch 0.55. A 31.03 cubic yard gravel pile is about 43.44 tons.

How many truckloads will it take to move the pile?

Divide the cubic yards by 10 for 10 cubic yard loads. A 31.03 cubic yard pile is 3.1 loads, so plan for 4 trips. Truck sizes and weight limits vary, so check with your hauler.

How we built this calculator: cone volume = π × r² × h ÷ 3, and rectangular piles use the prismoidal formula for straight sloped sides. Tons use the same planning densities as our yards to tons calculator. It is a planning estimate of loose pile volume: confirm with your supplier. Written and checked by the YardsCalculator editorial team.